series am1ss-z 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.a 1 of 2 north america only features: models single output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) efficiency (%) am1ss-0505sz 4.5-5.5 5 200 1000 74 am1ss-0512sz 4.5-5.5 12 83 1000 75 am1ss-0515sz 4.5-5.5 15 67 1000 75 am1ss-1205sz 10.8-13.2 5 200 1000 74 am1ss-1212sz 10.8-13.2 12 83 1000 75 am1ss-1215sz 10.8-13.2 15 67 1000 75 am1ss-2405sz 21.6-26.4 5 200 1000 74 am1ss-2412sz 21.6-26.4 12 83 1000 75 am1ss-2415sz 21.6-26.4 15 67 1000 76 AM1SS-0505SH30Z 4.5-5.5 5 200 3000 74 am1ss-0512sh30z 4.5-5.5 12 83 3000 75 am1ss-0515sh30z 4.5-5.5 15 67 3000 75 am1ss-1205sh30z 10.8-13.2 5 200 3000 74 am1ss-1212sh30z 10.8-13.2 12 83 3000 75 am1ss-1215sh30z 10.8-13.2 15 67 3000 75 am1ss-2405sh30z 21.6-26.4 5 200 3000 74 am1ss-2412sh30z 21.6-26.4 12 83 3000 75 am1ss-2415sh30z 21.6-26.4 15 67 3000 76 note: all specifications are measured at an ambient temperature of 25c, humidit y<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters nominal typical maximum units voltage range 5 12 24 4.5-5.5 10.8-13.2 21.6-26.4 vdc filter capacitor turn on transient process time 25 ms start up time 200 ms absolute ma ximum rating 5 vin 12 vin 24 vin 0-7 0-15 0-28 vdc peak input voltage time 100 ms input reflected ripple current with 12h 20 ma p-p isolation specifications parameters conditions typical rated units tested i/o voltage 3 sec 1000 and 3000 vdc resistance > 1000 mohm capacitance 10 pf output specifications parameters conditions typical maximum units voltage accuracy 3 % short circuit protection continuous ? rohs compliant ? operating temperature -40 o c to +85 o c ? 4 pin sip package ? input / output isolation 1000 and 3000vdc ? low ripple and noise ? pin compatible with multiple manufacturers ? high efficiency up to 76% ? continuous short circuit protection
series am1ss-z 1 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.a 2 of 2 north america only output specifications (continued) parameters conditions typical maximum units short circuit restart auto-recovery line voltage regulation for 1% change of vin 1.2 % of vin load voltage regulation load 20 ? 100% 10 % temperature coefficient 0.02 %/ o c ripple & noise at 20mhz bandwidth 100 mv p-p capacitive load 220 f rising time 50 ms general specifications parameters conditions typical maximum units switching frequency 100% load 80 khz operating temperature full load without derating -40 to +85 o c storage temperature -40 to +125 o c max case temperature 100 o c cooling free air convection humidity 95 % case material non-conductive black plastic ul94-vo weight 1.5 g dimensions (l x w x h) 0.46 x 0.24 x 0.40 inches 11.68 x 6.00 x 10.15 mm mtbf >1 121 000 hrs (mil-hdbk -217f, ground benign, t=+25 o c) safety specifications standards safety iec 60950-1 (designed to meet) pin out specifications dimensions note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com. pin single 1 - v input 2 +v input 3 - v output 4 +v output printed face 11.68 (0.46) 9.65 (0.38) 0.50 (0.02) 2.54 (0.10) 3.05 (0.12) 6.00 (0.24) 10.15 (0.40) 6.00 (0.24) 1.25 (0.05) 0.50 (0.02) 0.50 (0.02) 0.30 (0.10)
|
